
INTELLISTRIPE 380 USB/RS-232 DESKTOP MOTORIZED READER-ENCODER TECHNICAL REFERENCE MANUAL Manual Part Number 99875275-3 AUGUST 2007 R
IntelliStripe 380 2 APPLICABLE DOCUMENTS Standards ISO 7811-2, -3, -4, -5 Identification cards tracks 1-3 ISO 7810 Physical specificatio
Section 1. Features and Specifications 3Motorized Card Transport The Card Transport is based on an existing MagTek magstripe/encode module. Th
IntelliStripe 380 4 Spring-Loaded Card Registration Guide(s) The spring-loaded guide ensures that the reference edge of the card is mechanically
Section 1. Features and Specifications 5Direction of Magnetic Read: The ISO 7810 and 7811 specifications allow for bidirectional magnetic readi
IntelliStripe 380 6 Cable Management The following provisions are made for communication and power lines: • Polarization and locking of cable
Section 1. Features and Specifications 7RAM Space: 40 K bytes ROM Space: ROM Flash: Main Program Memory: 512 K Bytes Boot Loader Me
IntelliStripe 380 8 Opto-Sensor Inputs The Main PCB provides inputs for the three opto-sensors (Front, Encode, and Rear). Rotary Pulse Generato
Section 1. Features and Specifications 9External Auto-Ranging Power Pack The Reader/Encoder is powered from an external power-pack, which is lo
IntelliStripe 380 10 SPECIFICATIONS The Specifications are listed in Table 1-1. Table 1.1. Specifications OPERATING MSR Read-data Format Spec
11SECTION 2. INSTALLATION The installation of the IntelliStripe 380 Reader-Encoder consists of mounting the unit on a flat surface, connecting the
ii Copyright© 2001-2007 MagTek®, Inc. Printed in the United States of America Information in this document is subject to change without notice. N
IntelliStripe 380 12 Foot Pads (4)Mounting Screws #4-40 (3)5.7893.2301.6161.105.546 Figure 2-1. Dimensions for Mounting Holes for 3-Screw Set a
Section 2. Installation 13. Card Ejector RodMounting FlangeCard EjectorRodRear PanelGuide Slots &Attachment Holes Figure 2-3. Rear Panel an
IntelliStripe 380 14 CableP/N 16051417To PCPower Supply (with cable)P/N 64300091North American 110V Power Cord P/N 71100001 Figure 2-4. Cable
Section 2. Installation 15Cable connections for the USB are Shown in Figure 2-5, and the pin lists are shown in Table 2-2 and Table 2-3. Intell
IntelliStripe 380 16 Table 2-3. Cable Connections – USB Power P3 – 2.5 mm Power Jack Wire Color P4 – 10P10C RJ Plug Shell Gnd Drain Wire
Section 2. Installation 17Ejector Rod HoleFor Card RemovalPower And USB CableP/N 16051422Rear Panel Cover Figure 2-7. Rear Panel Cover Replaced
IntelliStripe 380 18
SECTION 3. OPERATION AND MAINTENANCE The operation of the unit includes inserting and removing the card. Maintenance includes keeping the unit cle
IntelliStripe 380 Shut power off by unplugging the power supply (Figure 2-4), and remove the card with the Rod as follows: 1. Remove the Rear Pa
21APPENDIX A. DIMENSIONS FOR MOUNTING MOUNTING The bottom of the unit is shown in Figure 2-1 and 2-2. The IntelliStripe 380 may be mounted in on
iii REGISTERED TO ISO 9001:2000 MagTek Part Number 99875275-1 1710 Apollo Court, Seal Beach, CA 90740 25 February 2003 Voice: 562-546-6400 Fax:
IntelliStripe 380 Figure A-1. Mounting Dimensions 1 22
Appendix A. Dimensions for Mounting 23 Figure A-2. Mounting Dimensions 2
IntelliStripe 380 24 Figure A-3. MagTek Mounting Plate, I380, 1
Appendix A. Dimensions for Mounting 25 Figure A-4. MagTek Mounting Plate, I380, 2
Appendix A. Dimensions for Mounting 26
iv FCC WARNING STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FC
v1112222244445556666667777788888888999999101111111111TABLE OF CONTENTS SECTION 1. FEATURES AND SPECIFICATIONS...
vi 1111121919191919212121212121Flange...
viiviii10121213141415151616171920202223242510141516TABLE OF FIGURES Figure 1-1. IntelliStripe 380-------------------------------------------------
viii Figure 1-1. IntelliStripe 380
1SECTION 1. FEATURES AND SPECIFICATIONS The IntelliStripe® 380, Desktop Motorized Reader-Encoder reads and encodes magnetic-stripe cards and smart
Komentarze do niniejszej Instrukcji