POST Error Messages

continued

1786 Slot 1 Drive Array Recovery Needed. The

following SCSI drive(s) need Automatic Data

Recovery: SCSI Port 1: SCSI ID 0

Select F1 to continue with recovery of data to

drive

Select F2 to continue without recovery

of data to drive

Slot 1 Drive Array Recovery Needed.

Automatic Data Recovery Previously Aborted!

The following SCSI drive(s) need Automatic

Data Recovery: SCSI Port 1: SCSI ID 0

Select to retry Automatic Data Recoveryto

drive

Select to continue without starting

Automatic Data Recovery data to drive.

data to drive

The message normally appears when a drive

was replaced in a fault-tolerant configuration

when system power was OFF. In this case,

press to start the automatic data recovery

process.

The “previously aborted” version of the 1786

POST message will appear if the previous

rebuild attempt was aborted for any reason.

Run Drive Array Advanced Diagnostics (DAAD)

for more information. If the replacement drive

was failed, try using another replacement drive.

If rebuild was aborted due to a read error from

another physical drive in the array, you’ll need

to back up all readable data on the array, run

Diagnostics Surface Analysis, and then restore

your data.

1787 Slot x Drive Array Operating in Interim

Recovery Mode. The following SCSI drive(s)

should be replaced:

SCSI Port (

): SCSI ID (

)

Following a system restart, this message

reminds you that drive

is defective and fault

tolerance is being used. Drive

needs

replacement as soon as possible. A loose or

defective cable may also cause this error.

1788 Slot x Drive Array Reports Incorrect Drive

Replacement. The following SCSI drive(s)

should have been replaced: SCSI Port (

SCSI ID (

)

The following SCSI drive(s) were incorrectly

replaced: SCSI Port (

): SCSI ID (z).

Select to continue - drive array will

remain disabled.

Select to reset configuration - all data

will be lost.

The drives indicated were installed in the wrong

place, so they have been disabled. Reinstall the

drives correctly.

Press to restart the computer with the drive

array disabled.

-Or-

Press to use the drives as configured and

lose all the data on them.

See NOTE below.

continued

1 2 ... 138 139 140 141 142 143 144 145 146 147 148 ... 161 162

Komentarze do niniejszej Instrukcji

Brak uwag

B&K Reference 7250 Series II manuály

Uživatelské manuály a uživatelské příručky pro Audio zesilovače B&K Reference 7250 Series II.
Poskytujeme 1 manuály pdf B&K Reference 7250 Series II ke stažení zdarma podle typů dokumentů: Manuál s instrukcemi

B k Reference 7250 Series II Manuál s instrukcemi (108 strany)

Značka: B-k | Kategorie: Audio amplifiers | Velikost: 2.28 MB |

Tabulka s obsahem

Instruction manual

Contents

Safety information

EC Declaration of Conformity

Overview of Transmitter

Assembly

Mounting plan

Fig.: Mounting plan

Fig.: Pipe-mount kit

Pipe mounting, panel mounting

Fig.: Panel-mount kit

Installation and connection

Division 2 wiring

Terminal assignments

Wiring examples

InPro 7250 HT sensor

Cond Ind 7100e/2(X)H

User interface and display

Operation: Keypad

Safety functions

Passcodes (factory setting)

Configuration

Menu group

Selection / Default

Individual settings

After correct input a

Code Display

Concentration measurement

0 ... 120 sec

Time constant 0 to 120 sec

Conductivity

 arrow key

Proceed with enter

(xxxx s)

Display Action

Calibration

Display

Display Action

Product calibration

Zero calibration in air

Measurement

Temperature probe adjustment

Diagnostics functions

Operating states

Error messages (Error Codes)

Display of last error message

Sensoface

Problem

Appendix

Specifications

Calibration solutions

Sodium chloride solutions

Concentration curves

-05- Nitric acid HNO

FM Control Drawing

Explosion protection

CSA Control Drawing

TA-194.301-MTE02 011005

108

Software version: 1.1

108

Další produkty a příručky pro Audio zesilovače B&K

Modely	Typ Dokumentu
Phono10	Uživatelský manuál Product Catalog, 46 stránky
FIVE OR SEVEN CHANNEL 125.5 S2	Servisní příručka B&K FIVE OR SEVEN CHANNEL 125.5 S2 Service manual, 241 stránky
AV1260	Uživatelský manuál B&K AV1260 Owner`s manual, 16 stránky
CT300.3	Uživatelský manuál Release Version 1.3.2, 29 stránky
Reference 125.5 Series II	Manuál B&K Reference 125.5 Series II Hardware manual, 56 stránky
200.7 S2	Provozní pokyny B&K 200.7 S2 Operating instructions, 34 stránky
50 Series II	Uživatelský manuál B&K 50 Series II Owner`s manual, 16 stránky
CT300.3	Uživatelský manuál B&K CT300.3 User manual, 88 stránky
ST3140	Uživatelský manuál B&K ST3140 Owner`s manual, 16 stránky
ST3030 Series II	Manuál s instrukcemi B&K ST3030 Series II Instruction manual, 144 stránky
Reference 125.5 Series II	Specifikace B&K Reference 125.5 Series II Specifications [en] , 46 stránky
200.1 S2	Uživatelský manuál B&K 200.1 S2 User manual, 12 stránky
AV2600	Uživatelská příručka B&K AV2600 User guide, 48 stránky
ST1400 Series II	Uživatelský manuál B&K Device Interface Protocol Series II, 37 stránky
50 Series II	Specifikace B&K 50 Series II Specifications, 16 stránky
ST55.2	Uživatelský manuál B&K ST55.2 Owner`s manual, 16 stránky
AV30.2	Uživatelský manuál Motioner till Svenska BÃ¥gskyttefÃ¶rbundets stÃ¤mma 2008 [en] , 30 stránky

Compaq 3100ES - Smart Array RAID Controller Podręcznik Użytkownika Strona 143

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Serwery Compaq 3100ES - Smart Array RAID Controller

B&K Reference 7250 Series II manuály

B k Reference 7250 Series II Manuál s instrukcemi (108 strany)

Tabulka s obsahem

Další produkty a příručky pro Audio zesilovače B&K